You may need to remove all the components from a printed circuit board for rework Cubs Anthony Rizzo Jersey , repair, upgrade, salvage or other purposes. But how do you do it in the most efficient way? It’s a simple process if you keep in mind that most printed circuit boards (PCBs) have both active and passive components that are attached to the PCB in one of two ways: surface-mounted or through-hole.
Surface mounted devices (SMDs) are electronic components that are soldered to the PCB surface by their miniscule metallic surface terminals. Common examples of SMDs are passive parts such as resistors are capacitors, or active parts such as ICs.
Through-hole components have leads that are inserted through padded holes and are then soldered to the pads on the bottom side of the PCB. Common examples of through-hole components are resistors, capacitors, relays, inductors, transformers and more.
To remove SMDs and through-hole components from a PCB, use the following procedure:
Preparation
1. Don personnel protective equipment (PPE) such as safety glasses and gloves.
2. Set the PCB on a work surface that is both horizontal and dry. It is important that the PCB is set on a truly horizontal surface; when the PCB is heated, molten solder will be created and may move to adjacent pads or tracing when set on a non-horizontal surface Cubs Jon Lester Jersey , which may cause short circuits on the PCB.
Removing SMDs
3. Use a heat gun to remove the SMDs. After turning on the heat gun, position it approximately 15 centimeters above the PCB with its nozzle pointed down. In short order, the heat will melt the solder flux of the SMDs that are beneath the nozzle of the heat gun. Quickly remove these components by utilizing a tweezers. Collect them in a tray. Repeat this procedure until all the SMDs are removed from the top side of the PCB.
4. After you have removed all the SMDs, allow the PCB to cool for up to three minutes. Power down the heat gun and properly stow it away in a safe place.
Removing Through-Hole Components
5. Energize a soldering iron and sets its temperature to 450oC. Obtain a 6-inch length of copper desoldering braid.
6. Select a desoldering starting point at the far edge of the board. Then touch the copper braid on top of a pad that as you place the tip of the soldering iron on the solder joint pad. In a matter of seconds, the solder flux should melt and flow into the copper braid. Follow this procedure for all pads.
7. After you have completed desoldering on the pads on the reverse side of the board, flip the PCB over and repeat the process again using both the heat gun and the soldering iron to remove any other components and residual solder.
8. When all SMD and through-hole components are removed, de-energize the soldering iron and properly secure it in a safe location.
Clean Up
9. Inspect the PCB and using swabs doused in alcohol, clean the pads on both sides of the PCB. After you have cleaned the pads, you should have removed all the components from the PCB. Make Sure To Properly Tag Your Luggage Before Traveling Subscribe to the e-newsletters of the major airlines. These types of e-newsletters give you vital information regarding special discounts and last-minute offers that is only available to subscribers. Yes, they will probably clutter your email Cubs Jason Heyward Jersey , but you'll save a good amount of money by putting up with this small problem.
Be sure to book your exact seat in order to help make your flight more comfortable. Frequently, airlines will allow you to select your seat preference for your flight, though occasionally it is not an option. Upon booking your flight, watch the booking site to see if this option is available. Being able to choose your own seat can make a huge difference.
Determine if you will need a Visa in order to go to the foreign country you are traveling to. If a visa will be required, apply for it early. Sometimes visas take weeks or even months to process, so it's best to be prepared ahead of time. Once again, without having the right kind of visa, you won't be able to get into certain countries.
Stores often overcharge for such products, and the space you save is minimal. Look for innovative ways to fold your clothing in a manner that saves space. Utilizing some of these methods can leave you with quite a bit more space in your bag.
Always remember to wear light, comfy shoes for air travel - shoes which you can slip off easily. You may need to take your shoes off during security checks. When traveling Chicago Cubs Anthony Rizzo Jersey , comfort is everything. You do not need particularly supportive shoes as you will be spending most of your time sitting. A perfect type of footwear for travelling is sandals.
If a hotel is fully booked, you can try asking to rent a room that is considered out of order. Rooms that need minor repairs, like a fresh coat of paint, are usually noted as being out-of-service.
Don't go to sleep before 8pm local time if you are adjusting to a different time zone. Although you may feel sleepy, if you go to bed to soon, you are only protracting your jet lag because your body is going to remain in its usual time-zone mode. You will overcome jet lag fast if you help your body quickly adjust to the time zone changes.
Utilize travel to educate your family. Even taking a trip to a developing nation can be a safe way to teach kids about the lives of people outside their home country. Time abroad is one of the best ways to learn to tolerate and understand other cultures.
Do not bring anything valuable that you will not need. Valuables attract attention and increase your risk of being a victim of theft.
If you flew to your destination and your checked baggage hasn't made it to you yet, don't go crazy. Locate the lost luggage statio. Wholesale NFL Jerseys Wholesale Jerseys China Wholesale Jerseys Cheap NFL Jerseys Cheap Jerseys From China Cheap Jerseys